Knoll-systems HD282 User Manual

HD282 HDTV DLP Projector Users Manual v1.1

10If the video device uses a VESA connector, plug a VESA cable into the video-out connector on the video device. Plug the other connector into the VE

11If the image is not square, adjust the keystone using the buttons on the keypad. Press the upper Keystone button to reduce the width of the upper p

12Shutting down the projector Power Save The projector has a Power Save feature in the System menu that automatically turns the lamp off after no sig

13The following table shows some potential problems. In some cases, more than one possible solution is provided. Try the solutions in the order they

14

15 Using the projector keypad buttons Most buttons are described in detail in other sections, but here is an overview of their functions: Power–tu

16Using the remote control The remote uses two (2) provided AAA batteries. They are easily installed by sliding the cover off the remote’s back, alig

17Optimizing video images After the video device is connected properly and the image is on the screen, you can optimize the image using the onscreen

18The menus are grouped by usage: The Picture menu provides image adjustments. The Settings menu provides set-up type adjustments that are not change

19 Native: this mode bypasses the internal scaler, displaying the image with no resizing. Since the native resolution is 1280x720 and 4x3 video imag

2FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. T

20 Natural Wide: this mode stretches a 4:3 image to fill the entire 16:9 screen. The center two-thirds of the image is unchanged; the edges of the i

21Advanced settings TrueLife: This option refers to Faroudja’s TrueLife processing of the image. All standard definition interlaced video signals (c

22Color Control: allows you to individually adjust the gain (relative warmth of the color) and the offset (the amount of black in the color) of the r

23The Source Enable feature is used to eliminate certain sources from this search, which will speed the search. By default, the check boxes for all s

24Blank Screen: determines what color displays when you press the Blank button on the remote or when no source is active. Language: allows you t

25Replacing the projection lamp The lamp hour timer in the About menu counts the number of hours the lamp has been in use. After 1980 hours, the mess

267. Tighten the single screw. 8. Replace the lamp door by sliding the tabs into the tab bays and tightening the two screws. 9. Plug in the power cab

27Red LED behavior and projector errors If the projector is not functioning properly and the red LED is blinking, consult the table below to determin

28

29

3TABLE OF CONTENTS Safety Warnings 2 Safety Instructions 4 Introduction/Usage guidelines 5 Setting up and positioning the projector

30RS232 Terminal Specifications and Commands To control the projector from an LCD control panel, connect an RS-232 cable to the serial control conn

31Supported commands Function Command Range Default Aspect Ratio ARZ 0-4 1 0 =Native 1 = 16:9 2 =

32 Green Gain GCG 1-63 32 High Power Enable HPE 0-1 0 Horizontal Position HPS n/a n/a Keystone (Vertical) DKC 53-203 128

33Red Gain RCG 1-63 32 Skintone Bypass Enable SBE 0-1 0 Source SRC 0-7 2 0 = Video 1, MI 1 = Vide

34 LIMITED WARRANTY Knöll Systems, Inc. (“Knöll”) warrants that each HD282 (“the Product”) sold hereunder will conform to and function in accordance

4SAFETY INSTRUCTIONS Please read and follow all safety instructions provided BEFORE using your new projector. Failure to comply with safety instruc

5INTRODUCTION The Knöll HD282 Introduction Congratulations and thank you for your choice of a superior digital image projection device. Your new Knöl

6SETTING UP THE PROJECTOR There are a number of factors to consider when determining where to set up the projector, including the size and shape of y

7HD282 Projection Distances 16:9 Image Screen Diagonal 92” 103” 106” 110” 122.5” 146.75” 165.25”Min. Distance 133.3” 149.6” 153.3” 160” 178.33” 21

8Video Connections 1. Place the projector on a flat surface or using a ceiling mount kit, on the ceiling. If you want to project from behind a rear

9Connecting a Video Device If your video device has more than one output, select the highest quality one. DVI video has the best quality, followed by