Knoll Systems Projector HDP2300 User Manual

HDP2300 High Definition ProjectorPROJECTORUser’s Manual

– 3 – ITEM LABEL DESCRIPTION SEE PAGE: 9. Horizontal lens shift Adjusts the image position horizontally 1910. Lens release button Press the rel

Top view—On-screen Display (OSD) buttons and LEDs ITEM LABEL DESCRIPTION SEE PAGE: 1. MENU Opens and exits OSD menus 2. ▲ (Up cursor) / Keyston

Rear view ITEM LABEL DESCRIPTION SEE PAGE: 1. VIDEO Connect the composite cable from a video device 2. YPbPr Connect a component video enable

– 6 – ITEM LABEL DESCRIPTION SEE PAGE: 12. VGA/ SCART/ YPbPr Connects the RGB cable from a computer and components 13. S-VIDEO Connects the S-

Bottom view ITEM LABEL DESCRIPTION SEE PAGE: 171. Tilt adjustor Rotate adjuster lever to adjust angle position. 2. Ceiling support holes Con

Remote Control Functions Important: 1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency fluo-rescent ligh

– 9 – ITEM LABEL DESCRIPTION SEE PAGE: 1. Power OFF Turns the projector off 132. HDMI 2 Displays the HDMI 2 source selection 3. S-VIDEO Disp

– 10 – Remote Control Operating Range The remote control uses infrared transmission to control the projector. It is not necessary to point the remote

SETUP AND OPERATION Inserting the Remote Control Batteries 1. Remove the battery compartment cover by sliding the cover in the direction of the arro

Connecting Input Devices A PC or notebook computer and video devices can be connected to the projector at the same time. Video devices include DVD, VC

Copyright This publication, including all photographs, illustrations and software, is protected under international copy-right laws, with all rights

Installing or Removing the Optional Lens Caution: y Do not shake or place excessive pressure on the projector or the lens components as the projec-tor

Installing the New Lens1. Align the notches and correctly position the electrical contact pad as shown in the picture. – 14 – Note: Pin of IRIS shoul

Starting and Shutting down the Projector Starting the projector 1. Remove the lens cap. 2. Securely connect the power cord and signal cable. When co

5. Turn on your source that you want to display on the screen (computer, note-book, video player, etc). The projector will detect the source automati

Adjusting the Projector Level Take note of the following when setting up the projector: • The projector table or stand should be level and sturdy. •

– 18 – Adjusting Projected Image Position Using Shift The Shift feature provides a lens shift function that can be used to adjust the position of the

– 19 – Adjusting the horizontal image position With the lens in the center position the horizontal image position can be adjusted to the left or right

Adjusting the Zoom ring, Focus and Keystone 1. Use the Image-zoom control (on the projector only) to resize the pro-jected image and screen size. 2

ON-SCREEN DISPLAY (OSD) MENU SETTINGS OSD Menu Controls The projector has an OSD that lets you make image adjustments and change various settings. Na

Setting the OSD Language Set the OSD language to your preference before continuing. 1. Press the MENU button. Press the cursor ◄► button to navigate

HDP2300 Users Manual — ii — Important Safety Information Important: It is strongly recommended that you read this section carefully before using the

OSD Menu Overview Use the following illustration to quickly find a setting or determine the range for a setting. – 23 – HDP2300 Users Manual

PICTURE: Basic Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the PICTURE: Basic menu. Press the cursor ▲▼ but

PICTURE: Advanced Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the PICTURE: Advanced menu. Press the cursor

HSG Adjustment Press the ENTER button to enter the HSG Adjustment sub menu. ITEM DESCRIPTION Press the ◄► buttons to set the Primary Color. Notes:

DISPLAY Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the DISPLAY menu. Press the cursor ▲▼ button to move u

PC Detail Adjustment Press the ENTER button to enter the PC Detail Adjustment sub menu. Note: Customizing the settings in PC Detail Adjustment menu is

SYSTEM SETUP: Basic Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the SYSTEM SETUP: Basic menu. Press the cu

Menu Settings Press the ENTER button to enter the Menu Settings sub menu. ITEM DESCRIPTION Press the ◄► buttons to select from five OSD locations:

SYSTEM SETUP: Advanced Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the SYSTEM SETUP: Advanced menu. Press

– 32 – Lamp Press the ENTER button to enter the Lamp sub menu. ITEM DESCRIPTION Lamp Mode Press the ◄► buttons to adjust lamp brightness. Reset La

Preface Projector Installation Notice ¾ Place the projector in a horizontal position The tilt angle of the projector should not exceed 15 degrees,

Closed Caption Press the ENTER button to enter the Closed Caption sub menu. ITEM DESCRIPTION Closed Caption Enable Press the ◄► buttons to turn on

INFORMATION Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the INFORMATION Menu. ITEM DESCRIPTION Source

MAINTENANCE AND SECURITY Replacing the Projection Lamp The projection lamp should be replaced when it burns out. It should only be replaced with a cer

6. Use a screwdriver to remove the screws from the lamp module. 7. Pull out the lamp module. 8. Reverse steps 1 to 7 to install the new lamp mod

– 37 – Cleaning the Projector Cleaning the projector to remove dust and grime will help ensure trouble-free operation. Warning: 1. Be sure to turn of

Using the Physical Lock ®Using the Kensington– 38 – Lock If you are concerned about security, attach the projector to a permanent object with the Ken

TROUBLESHOOTING Common problems and solutions These guidelines provide tips to deal with problems you may encounter while using the projector. If the

– 40 – LED Error Messages ERROR CODE MESSAGES POWER LEDBLINK READY LED BLINK TEMP LED BLINK Lamp Ready ON ON OFF Start ON OFF OFF Cooling ON FLASHI

– 41 – Image Problems Problem: No image appears on the screen 1. Verify the settings on your notebook or desktop PC. 2. Turn off all equipment and p

– 42 – Remote Control Problems Problem: The projector does not respond to the remote control 1. Direct the remote control towards remote sensor on t

Replacing the Lamp Replacing the lamp can be hazardous if done incorrectly. See Replacing the Projection Lamp on page 35 for clear and safe instructio

– 43 – HDMI Q & A Q. What is the difference between a “Standard” HDMI cable and a “High-Speed” HDMI cable? Recently, HDMI Licensing, LLC announce

— 44 — SPECIFICATIO NS Model HDP2300 Series Display type TI DLP DMD 0.65” Native Resolution 1920 x 1080 Weight 8.8 kg (19 lbs) Lens type Standard Lon

– 45 – Projection Distance vs. Projection Size HDP2300 Series Projection Distance and Size Table Standard projection lens: TR: 1.54 ~ 1.93 TELE WI

– 46 – The projector can display several resolutions. The following table outlines the resolutions that can be displayed by the projector. SIGNAL RES

– 47 – SIGNAL RESOLUTION H-SYNC (KHZ) V-SYNC(HZ) COMPOSITE / S-VIDEOCOMPONENT RGB (ANALOG) HDMI (DIGITAL)640 x 480 37.9 72.8 — — O O 800 x 60

– 48 – SIGNAL RESOLUTION H-SYNC (KHZ) V-SYNC(HZ) COMPOSITE / S-VIDEOCOMPONENT RGB (ANALOG) HDMI (DIGITAL)720p 45.0 60.0 O — — O 720p 37.5 50.0

Projector Dimensions – 49 – HDP2300 Users Manual

REGULATORY COMPLIANCE FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device pur-suant to Part 15

– v – Table of Contents GETTING STARTED...

— vi — TROUBLESHOOTING ...

– 1 – GETTING STARTED Packing Checklist Carefully unpack the projector and check that the following items are included: HDP2300 SERIES PROJECTOR WIT

Views of Projector Parts HDP2300 Series Front-right View ITEM LABEL DESCRIPTION SEE PAGE: 1. IR receiver Receives IR signal from remote control